SMC气缸的使用注意事项

襄阳德而尼自动化设备有限公司销售SMC日本SMC,日本SMC气缸,日本SMC电磁阀,日本SMC气动产品洽谈，

SMC气缸的使用注意事项如下

1,对使用环境的要求在灰尘多、有水滴的场所，杆侧应带伸缩防护套，安装时，不要出现拧扭状态。不能使用伸缩防护套的场所，应选用带力防尘圈的气缸或防水气缸。关于气缸的润滑给油润滑气缸，应配置流量合适的油雾器。2.关于气缸的负载活塞杆通常只能承受轴向负载。要避免在活塞杆施加横向负载和偏心负载。有横向负载时，活塞杆应加导向装置，或选用到导杆气缸    3.关于气缸的安装安装固定式气缸时，负载和活塞杆的轴线要致。安装耳环式和耳轴式气缸时，应保证气缸的摆动和负载的摆动在个平面内。不然，轻则密封件偏磨，造成漏气，使气缸使用寿命降；重气缸不动作。有时，气缸还会出现冲击动作，可能造成人身和装置的损伤。气缸现场安装时，要防止钻孔的切屑末从气缸的进气口混入缸内。脚座式气缸若在脚座有定位孔，可用于定位耳轴式轴承支座的安装面离轴承的距离较时，要注意安装面的安装螺钉不得受力太而损坏。用固定式气缸使连接臂作圆弧运动时，可在臂开形孔，所开形孔应考虑到在导向套受的横向负载不要过规定值。销轴之类的回转要涂润滑脂，以防止烧结。对空气质量的要求要使用清洁干燥的压缩空气。空气中不得含有机溶剂的合成油、盐分、腐蚀性气体等，以防缸、阀动作不良。安装前，连接配管内应充分吹洗，不要将灰尘、切削末、密封带碎片等杂质带入缸、阀内,www.san17.com
Xiangyang German and Nepalese special sales automation equipment Co., Ltd. Japan SMC SMC, Japan, SMC cylinder, Japan SMC solenoid valve, Japan SMC pneumatic products please call to discuss,

Note the use of SMC cylinder as

1, the requirements for use in a dusty environment, a drop of water in places, with a escopic rod side of the protective cover should be installed, do not appear twist state. You can not use retractable protective sleeves in place, should be used with strong dust ring of the cylinder or water cylinder. On the cylinder lubrication oil lubrication to the cylinder, you should configure the appropriate flow lubricator. （2） the load on the cylinder piston rod is usually only axial load. To avoid lateral load applied on the piston rod and eccentric load. A lateral load, the piston rod guide should be added, or used to guide cylinder 3 cylinder Installation on fixed cylinder, the load and the axis of the piston rod to be consistent. Trunnion-style earrings and install the cylinder, the cylinder should ensure that the load swing and swing in a plane. Otherwise, ranging from partial seal wear, resulting in leakage, reduce the life of the cylinder; heavy cylinder does not move. Sometimes, there will be the impact of the cylinder moves, and the device can lead to personal injury. Cylinders on-site installation, drilling cuttings at the end to prevent the inlet from the cylinder mix cylinder. Foot cylinder seat if there are holes in the feet, can be used to position the trunnion bearings bearing mounting surface of the large distance from the bearing, pay attention to the mounting surface of the mounting screws must not force too much damage. Cylinder with a fixed arm for circular motion to make the connection, you can open a long-shaped hole in the arm, the opening should take into account long-shaped hole in the horizontal direction by the load put on no more than the specified value. Like the rotation pin coated with grease to in order to prevent sintering. Air quality requirements to the use of clean dry compressed air. Air shall not contain organic solvents in synthetic oil, salt, corrosive gases, etc., to prevent the cylinder, valve action bad. Before installation, the pipe should be fully connected with the purge, not to dust, the cutting end, sealed with debris and other impurities into the cylinder, valve